●The STM32L432xx devices are the ultra-low-power microcontrollers based on the high-performance ARM® Cortex®-M4 32-bit RISC core operating at a frequency of up to 80 MHz. The Cortex-M4 core features a Floating point unit (FPU) single precision which supports all ARM single-precision data-processing instructions and data types. It also implements a full set of DSP instructions and a memory protection unit (MPU) which enhances application security.
●The STM32L432xx devices embed high-speed memories ( Flash memory up to 256 Kbyte, 64 Kbyte of SRAM), a Quad SPI flash memories interface and an extensive range of enhanced I/Os and peripherals connected to two APB buses, two AHB buses and a 32-bit multi-AHB bus matrix.
●The STM32L432xx devices embed several protection mechanisms for embedded Flash memory and SRAM: readout protection, write protection, proprietary code readout protection and Firewall.
●The devices offer a fast 12-bit ADC (5 Msps), two comparators, one operational amplifier, twoDAC channels, a low-power RTC, one general-purpose 32-bit timer, one 16-bit PWM timer dedicated to motor control, four general-purpose 16-bit timers, and two 16-bit low-power timers.
●In addition, up to 3 capacitive sensing channels are available.
●They also feature standard and advanced communication interfaces.
●Key Features
● Ultra-low-power with FlexPowerControl
● 1.71 V to 3.6 V power supply
● -40 °C to 85/105/125 °C temperature range
● 8 nA Shutdown mode (2 wakeup pins)
● 28 nA Standby mode (2 wakeup pins)
● 280 nA Standby mode with RTC
● 1.0 μA Stop 2 mode, 1.28 μA with RTC
● 84 μA/MHz run mode
● Batch acquisition mode (BAM)
● 4 μs wakeup from Stop mode
● Brown out reset (BOR)
● Interconnect matrix
● Core: ARM® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait-state execution from Flash memory, frequency up to 80 MHz, MPU, 100DMIPS and DSP instructions
● Performance benchmark
● 1.25 DMIPS/MHz (Drystone 2.1)
● 273.55 CoreMark® (3.42 CoreMark/MHz @ 80 MHz)
● Energy benchmark
● 176.7 ULPBench® score
● Clock Sources
● 32 kHz crystal oscillator for RTC (LSE)
● Internal 16 MHz factory-trimmed RC (±1%)
● Internal low-power 32 kHz RC (±5%)
● Internal multispeed 100 kHz to 48 MHz oscillator, auto-trimmed by LSE (better than ±0.25 % accuracy)
● Internal 48 MHz with clock recovery
● 2 PLLs for system clock, USB, audio, ADC
● Up to 26 fast I/Os, most 5 V-tolerant
● RTC with HW calendar, alarms and calibration
● Up to 3 capacitive sensing channels
● 11x timers: 1x 16-bit advanced motor-control, 1x 32-bit and 2x 16-bit general purpose, 2x 16-bit basic, 2x low-power 16-bit timers (available in Stop mode), 2x watchdogs, SysTick timer
● Memories
● Up to 256 KB single bank Flash, proprietary code readout protection
● 64 KB of SRAM including 16 KB with hardware parity check
● Quad SPI memory interface
● Rich analog peripherals (independent supply)
● 1× 12-bit ADC 5 Msps, up to 16-bit with hardware oversampling, 200 μA/Msps
● 2x 12-bit DAC, low-power sample and hold
● 1x operational amplifier with built-in PGA
● 2x ultra-low-power comparators
● 14x communication interfaces
● USB 2.0 full-speed crystal less solution with LPM and BCD
● 1x SAI (serial audio interface)
● 2x I2C FM+(1 Mbit/s), SMBus/PMBus
● 3x USARTs (ISO 7816, LIN, IrDA, modem)
● 1x LPUART (Stop2 wake-up)
● 2x SPIs (3x SPIs with the Quad SPI)
● CAN (2.0B Active)
● SWPMI single wire protocol master I/F
● IRTIM (Infrared interface)
● 14-channel DMA controller
● True random number generator
● CRC calculation unit, 96-bit unique ID
