● High-Performance Static CMOS Technology
● 150 MHz (6.67-ns Cycle Time)
● Low-Power (1.8-V Core at 135 MHz, 1.9-V Core at 150 MHz, 3.3-V I/O) Design
● JTAG Boundary Scan Support IEEE Standard 1149.1-1990 IEEE Standard Test Access Port and Boundary-Scan Architecture
● High-Performance 32-Bit CPU (TMS320C28x)
● 16 x 16 and 32 x 32 MAC Operations
● 16 x 16 Dual MAC
● Harvard Bus Architecture
● Atomic Operations
● Fast Interrupt Response and Processing
● Unified Memory Programming Model
● 4M Linear Program/Data Address Reach
● Code-Efficient (in C/C++ and Assembly)
● TMS320F24x/LF240x Processor Source Code Compatible
● On-ChipMemory
● Flash Devices: Up to 128K x 16 Flash (Four 8K x 16 and Six 16K x 16 Sectors)
● ROM Devices: Up to 128K x 16 ROM
● 1K x 16 OTP ROM
● L0 and L1: 2 Blocks of 4K x 16 Each Single-Access RAM (SARAM)
● H0: 1 Block of 8K x 16 SARAM
● M0 and M1: 2 Blocks of 1K x 16 Each SARAM
● Boot ROM (4K x16)
● With Software Boot Modes
● Standard Math Tables
● External Interface(2812)
● Over 1M x 16 Total Memory
● Programmable Wait States
● Programmable Read/Write Strobe Timing
● Three Individual Chip Selects
● Endianness: Little Endian
● Clock and SystemControl
● Dynamic PLL Ratio Changes Supported
● On-Chip Oscillator
● Watchdog Timer Module
● Three ExternalInterrupts
● Peripheral Interrupt Expansion (PIE) Block That Supports 45Peripheral Interrupts
● Three 32-Bit CPU-Timers
● 128-BitSecurity Key/Lock
● Protects Flash/ROM/OTP and L0/L1 SARAM
● Prevents Firmware Reverse-Engineering
● Motor ControlPeripherals
● Two Event Managers (EVA, EVB)
● Compatible to 240xA Devices
● Serial PortPeripherals
● Serial Peripheral Interface (SPI)
● Two Serial Communications Interfaces (SCIs), Standard UART
● Enhanced Controller Area Network (eCAN)
● Multichannel Buffered Serial Port (McBSP)
● 12-Bit ADC, 16Channels
● 2 x 8 Channel Input Multiplexer
● Two Sample-and-Hold
● Single/Simultaneous Conversions
● Fast Conversion Rate: 80 ns/12.5 MSPS
● Up to 56General-Purpose I/O (GPIO) Pins
● Advanced EmulationFeatures
● Analysis and Breakpoint Functions
● Real-Time Debug via Hardware
● Development ToolsInclude
● ANSI C/C++ Compiler/Assembler/Linker
● Code Composer Studio IDE
● DSP/BIOS
● JTAG Scan Controllers(1)
● Low-PowerModes and Power Savings
● IDLE, STANDBY, HALT Modes Supported
● Disable Individual Peripheral Clocks
● PackageOptions
● 179-Ball MicroStar BGA With External Memory Interface (GHH, ZHH) (2812)
● 176-Pin Low-Profile Quad Flatpack (LQFP) With External Memory Interface (PGF) (2812)
● 128-Pin LQFP Without External Memory Interface (PBK) (2810, 2811)
● Temperature Options
● A: –40°C to 85°C (GHH, ZHH, PGF, PBK)
● S: –40°C to 125°C (GHH, ZHH, PGF, PBK)
● Q: –40°C to 125°C (PGF, PBK) [Q100 Qualification]
Part 3D Model
