TMS320LF2407 Datasheet PDF - TI

●The TMS320LF240x devices, new members of the TMS320C24x™ generation of digital signal processor (DSP) controllers, are part of the TMS320C2000™ platform of fixed-point DSPs. The 240x devices offer the enhanced TMS320™ DSP architectural design of the C2xx core CPU for low-cost, low-power, and high-performance processing capabilities. Several advanced peripherals, optimized for digital motor and motion control applications, have been integrated to provide a true single-chip DSP controller. While code-compatible with the existing C24x™ DSP controller devices, the 240x offers increased processing performance (30 MIPS) and a higher level of peripheral integration. See the TMS320x240x Device Summary section for device-specific features.

●The 240x generation offers an array of memory sizes and different peripherals tailored to meet the specific price/performance points required by various applications. Flash devices of up to 32K words offer a cost-effective reprogrammable solution for volume production. Note that Flash-based devices contain a 256-word boot ROM to facilitate in-circuit programming. The 240x family also includes ROM devices that are fully pin-to-pin compatible with their Flash counterparts. (The ROM devices are described in the SPRS145 data sheet.)

●All 240x devices offer at least one event manager module which has been optimized for digital motor control and power conversion applications. Capabilities of this module include center- and/or edge-aligned PWM generation, programmable deadband to prevent shoot-through faults, and synchronized analog-to-digital conversion. Devices with dual event managers enable multiple motor and/or converter control with a single 240x DSP controller.

●The high-performance, 10-bit analog-to-digital converter (ADC) has a minimum conversion time of 500 ns and offers up to 16 channels of analog input. The autosequencing capability of the ADC allows a maximum of 16 conversions to take place in a single conversion session without any CPU overhead.

●A serial communications interface (SCI) is integrated on all devices to provide asynchronous communication to other devices in the system. For systems requiring additional communication interfaces, the 2407 and 2406 offer a 16-bit synchronous serial peripheral interface (SPI). The 2407 and 2406 also offer a controller area network (CAN) communications module that meets 2.0B specifications. To maximize device flexibility, functional pins are also configurable as general-purpose inputs/outputs (GPIOs).

●To streamline development time, JTAG-compliant scan-based emulation has been integrated into all devices. This provides non-intrusive real-time capabilities required to debug digital control systems. A complete suite of code-generation tools from C compilers to the industry-standard Code Composer Studio™ debugger supports this family. Numerous third-party developers not only offer device-level development tools, but also system-level design and development support.

● TMS320LF2407, TMS320LF2406, and TMS320LF2402 are Being Replaced by TMS320LF2407A, TMS320LF2406A, and TMS320LF2402A, Respectively. Hence, TMS320LF2407, TMS320LF2406, and TMS320LF2402 are NOT RECOMMENDED FOR NEW DESIGNS (NRND).

● High-Performance Static CMOS Technology

● 33-ns Instruction Cycle Time (30 MHz)

● 30-MIPS Performance

● Low-Power 3.3-V Design

● Based on TMS320C2xx DSP CPU Core

● Code-Compatible With F243/F241/C242

● Instruction Set and Module Compatible With F240/C240

● On-Chip Memory

● Up to 32K Words x 16 Bits of Flash EEPROM (4 Sectors)

● Up to 2.5K Words x 16 Bits of Data/Program RAM

● 544 Words of Dual-Access RAM

● Up to 2K Words of Single-Access RAM

● Boot ROM

● SCI/SPI Bootloader

● Two Event-Manager (EV) Modules (EVA and EVB), Each Include:

● Two 16-Bit General-Purpose Timers

● Eight 16-Bit Pulse-Width Modulation (PWM) Channels Which Enable:

● Three-Phase Inverter Control

● Center- or Edge-Alignment of PWM Channels

● Emergency PWM Channel Shutdown With External PDPINTx\ Pin

● Programmable Deadband (Deadtime) Prevents Shoot-Through Faults

● Three Capture Units For Time-Stamping of External Events

● On-Chip Position Encoder Interface Circuitry

● Synchronized Analog-to-Digital Conversion

● Designed for AC Induction, BLDC, Switched Reluctance, and Stepper Motor Control

● Applicable for Multiple Motor and/or Converter Control

● External Memory Interface (LF2407)

● 192K Words x 16 Bits of Total Memory:

●64K Program, 64K Data, 64K I/O

● Watchdog (WD) Timer Module

● 10-Bit Analog-to-Digital Converter (ADC)

● 8 or 16 Multiplexed Input Channels

● 500 ns Minimum Conversion Time

● Selectable Twin 8-Input Sequencers Triggered by Two Event Managers

● Controller Area Network (CAN) 2.0B Module

● Serial Communications Interface (SCI)

● 16-Bit Serial Peripheral Interface (SPI) Module

● Phase-Locked-Loop (PLL)-Based Clock Generation

● Up to 40 Individually Programmable, Multiplexed General-Purpose Input/Output (GPIO) Pins

● Up to Five External Interrupts (Power Drive Protection, Reset, and Two Maskable Interrupts)

● Power Management:

● Three Power-Down Modes

● Ability to Power Down Each Peripheral Independently

● Real-Time JTAG-Compliant Scan-Based Emulation, IEEE Standard 1149.1 (JTAG)

● Development Tools Include:

● Texas Instruments (TI) ANSI C Compiler, Assembler/Linker, and Code Composer Studio™ Debugger

● Evaluation Modules

● Scan-Based Self-Emulation (XDS510™)

● Broad Third-Party Digital Motor Control Support

● Package Options

● 144-Pin Low-Profile Quad Flatpack (LQFP) PGE (LF2407)

● 100-Pin LQFP PZ (LF2406)

● 64-Pin Quad Flatpack (QFP) PG (LF2402)

● Extended Temperature Options (A and S)

● A: –40°C to 85°C

● S: –40°C to 125°C

●Code Composer Studio and XDS510 are trademarks of Texas Instruments.

●IEEE Standard 1149.1–1990, IEEE Standard Test-Access Port

●TMS320C24x, TMS320C2000, TMS320, and C24x are trademarks of Texas Instruments.

●Other trademarks are the property of their respective owners.

●Throughout this data sheet, 240x is used as a generic name for LF240x devices.