XPC860PZP80NN Datasheet PDF - Motorola

●Overview

●The MPC860 Quad Integrated Communications Controller (PowerQUICC™) is a versatile one-chip integrated microprocessor and peripheral combination designed for a variety of controller applications. It particularly excels in both communications and networking systems. The PowerQUICC unit is referred to as the MPC860 in this manual.

●Features

●The following list summarizes the key MPC860 features:

●• Embedded single-issue, 32-bit MPC8xx core (implementing the PowerPC architecture) with thirty-two 32-bit general-purpose registers (GPRs)

●— The core performs branch prediction with conditional prefetch, without conditional execution

●— 4- or 8-Kbyte data cache and 4- or 16-Kbyte instruction cache (see Table 1)

●  – 16-Kbyte instruction caches are four-way, set-associative with 256 sets;

●     4-Kbyte instruction caches are two-way, set-associative with 128 sets.

●  – 8-Kbyte data caches are two-way, set-associative with 256 sets; 4-Kbyte data caches are two-way, set-associative with 128 sets.

●  – Cache coherency for both instruction and data caches is maintained on 128-bit (4-word) cache blocks.

●  – Caches are physically addressed, implement a least recently used (LRU) replacement algorithm, and are lockable on a cache block basis.

●— Instruction and data caches are two-way, set-associative, physically addressed, LRU replacement, and lockable on-line granularity.

●— MMUs with 32-entry TLB, fully associative instruction, and data TLBs

●— MMUs support multiple page sizes of 4, 16, and 512 Kbytes, and 8 Mbytes; 16 virtual address spaces and 16 protection groups

●— Advanced on-chip-emulation debug mode

●• Up to 32-bit data bus (dynamic bus sizing for 8, 16, and 32 bits)

●• 32 address lines

●• Operates at up to 80 MHz

●• Memory controller (eight banks)

●— Contains complete dynamic RAM (DRAM) controller

●— Each bank can be a chip select or RASto support a DRAM bank

●— Up to 15 wait states programmable per memory bank

●— Glueless interface to DRAM, SIMMS, SRAM, EPROM, Flash EPROM, and other memory devices.

●— DRAM controller programmable to support most size and speed memory interfaces

●— Four CASlines, four WElines, one OEline

●— Boot chip-select available at reset (options for 8-, 16-, or 32-bit memory)

●— Variable block sizes (32 Kbyte to 256 Mbyte)

●— Selectable write protection

●— On-chip bus arbitration logic

●• General-purpose timers

●— Four 16-bit timers or two 32-bit timers

●— Gate mode can enable/disable counting

●— Interrupt can be masked on reference match and event capture

●• System integration unit (SIU)

●— Bus monitor

●— Software watchdog

●— Periodic interrupt timer (PIT)

●— Low-power stop mode

●— Clock synthesizer

●— Three parallel I/O registers with open-drain capability

●• Four baud-rate generators (BRGs)

●— Independent (can be connected to any SCC or SMC)

●— Allow changes during operation

●— Autobaud support option

●• Four serial communications controllers (SCCs)

●— Ethernet/IEEE 802.3 optional on SCC1–4, supporting full 10-Mbps operation (available only on specially programmed devices).

●— HDLC/SDLC(all channels supported at 2 Mbps)

●— HDLC bus (implements an HDLC-based local area network (LAN))

●— Asynchronous HDLC to support PPP (point-to-point protocol)

●— AppleTalk

●— Universal asynchronous receiver transmitter (UART)

●— Synchronous UART

●— Serial infrared (IrDA)

●— Binary synchronous communication (BISYNC)

●— Totally transparent (bit streams)

●— Totally transparent (frame based with optional cyclic redundancy check (CRC))

●• Two SMCs (serial management channels)

●— UART

●— Transparent

●— General circuit interface (GCI) controller

●— Can be connected to the time-division multiplexed (TDM) channels

●• One SPI (serial peripheral interface)

●— Supports master and slave modes

●— Supports multimaster operation on the same bus

●• One I2C (inter-integrated circuit) port

●— Supports master and slave modes

●— Multiple-master environment support

●• Time-slot assigner (TSA)

●— Allows SCCs and SMCs to run in multiplexed and/or non-multiplexed operation

●— Supports T1, CEPT, PCM highway, ISDN basic rate, ISDN primary rate, user defined

●— 1- or 8-bit resolution

●— Allows independent transmit and receive routing, frame synchronization, clocking

●— Allows dynamic changes

●— Can be internally connected to six serial channels (four SCCs and two SMCs)

●• Parallel interface port (PIP)

●— Centronics interface support

●— Supports fast connection between compatible ports on the MPC860 or the MC68360

●• PCMCIA interface

●— Master (socket) interface, release 2.1 compliant

●— Supports two independent PCMCIA sockets

●— Eight memory or I/O windows supported

●• Low power support

●— Full on—all units fully powered

●— Doze—core functional units disabled, except time base decrementer, PLL, memory controller, RTC, and CPM in low-power standby

●— Sleep—all units disabled, except RTC and PIT, PLL active for fast wake up

●— Deep sleep—all units disabled including PLL, except RTC and PIT

●— Power down mode— all units powered down, except PLL, RTC, PIT, time base, and decrementer

●• Debug interface

●— Eight comparators: four operate on instruction address, two operate on data address, and two operate on data

●— Supports conditions: =≠<>

●— Each watchpoint can generate a break-point internally

●• 3.3 V operation with 5-V TTL compatibility except EXTAL and EXTCLK

●• 357-pin ball grid array (BGA) package