Part Datasheet Search > Microcontrollers > LPC1857 Datasheet PDF
Images are for reference
LPC1857 Datasheet PDF
Part Series:
LPC1857 Series
Category:
Microcontrollers
Description:
MCU 32Bit LPC1800 ARM Cortex M3 RISC 1024KB Flash 2.5V/3.3V 256Pin LBGA Tray
Updated Time: 2023/01/13 03:08:16 (UTC + 8)
LPC1857 Microcontrollers Datasheet PDF
LPC1857 Datasheet PDF Microcontrollers
LPC1857FET256,551 - NXP Specifications
TYPE
DESCRIPTION
Mounting Style
Surface Mount
Frequency
180 MHz
Number of Pins
256 Pin
Supply Voltage (DC)
2.20V (min)
Case/Package
LBGA-256
show more
LPC1857FET256,551 - NXP Function Overview
●Overview
●The LPC185x/3x/2x/1x are ARM Cortex-M3 based microcontrollers for embedded applications. The ARM Cortex-M3 is a next generation core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration.
●The LPC185x/3x/2x/1x operate at CPU frequencies of up to 180 MHz. The ARM Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals. The ARM Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branching.
●The LPC185x/3x/2x/1x include up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, a quad SPI Flash Interface (SPIFI), a State Configurable Timer (SCT) subsystem, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals.
●MoreLess
●## Features
● Processor core
● ARM Cortex-M3 processor, running at CPU frequencies of up to 180 MHz
● ARM Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions
● ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
● Non-maskable Interrupt (NMI) input
● JTAG and Serial Wire Debug, serial trace, eight breakpoints, and four watch points
● Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support
● System tick timer
● On-chip memory
● Up to 1 MB on-chip dual bank flash memory with flash accelerator
● 16 kB on-chip EEPROM data memory
● 136 kB SRAM for code and data use
● Multiple SRAM blocks with separate bus access
● 64 kB ROM containing boot code and on-chip software drivers
● 64 bit of One-Time Programmable (OTP) memory for general-purpose use
● Clock generation unit
● Crystal oscillator with an operating range of 1 MHz to 25 MHz
● 12 MHz internal RC oscillator trimmed to 2 % accuracy over temperature and voltage (1 % accuracy for Tamb = 0 °C to 85 °C)
● Ultra-low power RTC crystal oscillator
● Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL can be used with the High-speed USB, the third PLL can be used as audio PLL
● Clock output
● Configurable digital peripherals
● State Configurable Timer (SCT) subsystem on AHB
● Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like timers, SCT, and ADC0/1
● Serial interfaces
● Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 52 MB per second
● 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2)
● One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY (USB0)
● One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to an external high-speed PHY (USB1)
● USB interface electrical test software included in ROM USB stack
● Four 550 UARTs with DMA support: one UART with full modem interface; one UART with IrDA interface; three USARTs support UART synchronous mode and a smart card interface conforming to ISO7816 specification
● Up to two C_CAN 2.0B controllers with one channel each. Use of C_CAN controller excludes operation of all other peripherals connected to the same bus bridge
● Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support
● One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s
● One standard I²C-bus interface with monitor mode and standard I/O pins
● Two I²S interfaces with DMA support, each with one input and one output
● Digital peripherals
● External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices
● LCD controller with DMA support and a programmable display resolution of up to 1024H x 768V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping
● SD/MMC card interface
● Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB slaves
● Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors
● GPIO registers are located on the AHB for fast access. GPIO ports have DMA support
● Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources
● Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins
● Four general-purpose timer/counters with capture and match capabilities
● One motor control PWM for three-phase motor control
● One Quadrature Encoder Interface (QEI)
● Repetitive Interrupt timer (RI timer)
● Windowed watchdog timer
● Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes of battery powered backup registers
● Event recorder with three inputs to record event identification and event time; can be battery powered
● Alarm timer; can be battery powered
● Analog peripherals
● One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
● Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight analog channels total. Each analog input is connected to both ADCs
● Unique ID for each device
● Power
● Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip internal voltage regulator for the core supply and the RTC power domain
● RTC power domain can be powered separately by a 3 V battery supply
● Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down
● Processor wake-up from Sleep mode via wake-up interrupts from various peripherals
● Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain
● Brownout detect with four separate thresholds for interrupt and forced reset
● Power-On Reset (POR)
● Available in LQFP208, LBGA256, LQFP144, and TFBGA100 packages
●## Target Applications
● Industrial
● Consumer
● White goods
● RFID readers
● e-Metering
●## Features
show more
Part Datasheet PDF Search
Example: STM32F103
Loading...
72,405,303 Parts Datasheet PDF, Update more than 5,000 PDF files ervery day.