Web Analytics
Part Datasheet Search > LED Drivers > PCA9533 Datasheet PDF
Images are for reference

PCA9533 Datasheet PDF

Part Series:
PCA9533 Series
Category:
LED Drivers
Description:
LED Driver 2.5V/3.3V/5V 8Pin SO T/R
Updated Time: 2023/01/13 02:46:37 (UTC + 8)

PCA9533 Datasheet PDF LED Drivers

158 Pages
NXP
LED Driver 2.5V/3.3V/5V 8Pin TSSOP T/R
158 Pages
NXP
LED Driver 2.5V/3.3V/5V 8Pin SO Bulk

PCA9533D/01,118 - NXP Specifications

TYPE
DESCRIPTION
Mounting Style
Surface Mount
Frequency
400 kHz
Number of Pins
8 Pin
Case/Package
SOT-96-1
Number of Outputs
4 Output
show more

PCA9533D/01,118 - NXP Function Overview

Overview
The PCA9533 is a 4-bit I²C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications.
The PCA9533 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED.
The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 100 mA per package.
To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chip set, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8574 or PCA9554. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc.
The Power-On Reset (POR) initializes the registers to their default state, causing the bits to be set HIGH (LED off).
Due to pin limitations, the PCA9533 is not featured with hardware address pins. The PCA9533/01 and the PCA9533/02 have different fixed I²C-bus addresses allowing operation of both on the same bus.
MoreLess
## Features
4 LED drivers (on, off, flashing at a programmable rate)
Two selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 second and 6.58 milliseconds)
256 brightness steps
Input/outputs not used as LED drivers can be used as regular GPIOs
Internal oscillator requires no external components
I²C-bus interface logic compatible with SMBus
Internal power-on reset
Noise filter on SCL/SDA inputs
4 open-drain outputs directly drive LEDs to 25 mA
Edge rate control on outputs
No glitch on power-up
Supports hot insertion
Low standby current
Operating power supply voltage range of 2.3 V to 5.5 V
0 Hz to 400 kHz clock frequency
ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Packages offered: SO8, TSSOP8 (MSOP8)
## Features
show more
Part Datasheet PDF Search
Loading...
72,405,303 Parts Datasheet PDF, Update more than 5,000 PDF files ervery day.

Relate Parts