●Overview
●The LPC4320FBD144 is an ARM Cortex-M4 based digital signal controller with an ARM Cortex-M0 coprocessor designed for embedded applications requiring signal processing. The ARM Cortex-M4 core offers single-cycle Multiply-Accumulate and SIMD instructions and a hardware floating-point unit to support signal processing while the M0 coprocessor handles I/O and digital control processing. The LPC4320FBD144 includes 168 kB of data memory, one High Speed USB 2.0 Host/OTG/Device, advanced configurable peripherals such as the State Configurable Timer (SCT), Serial General Purpose I/O (SGPIO), and SPI Flash Interface (SPIFI) as well as an external memory controller and multiple digital and analog peripherals.
●MoreLess
●## Features
● ARM Cortex-M4 processor, running at frequencies of up to 204 MHz
● ARM Cortex-M4 built-in Memory Protection Unit (MPU) supporting eight regions
● ARM Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC)
● Hardware floating-point unit
● Non-maskable Interrupt (NMI) input
● JTAG and Serial Wire Debug (SWD)
● System tick timer
● ARM Cortex-M0 co-processor running at frequencies of up to 204 MHz
● 200 kB SRAM for code and data use
● Two 32 kB SRAM blocks with separate bus access
● 32 kB ROM containing boot code and on-chip software drivers
● 32 bit One-Time Programmable (OTP) memory for customer use
● Serial GPIO (SGPIO) interface
● State Configurable Timer (SCT) subsystem on AHB
● Quad SPI Flash Interface (SPIFI) with four lanes and up to 40 MB per second
● One High-speed USB 2.0 Host/Device/OTG interface with DMA support
● One 550 UART with DMA support and full modem interface
● Three 550 USARTs with DMA and synchronous mode support
● One C_CAN 2.0B controller with one channel
● Two SSP controllers with FIFO and multi-protocol support
● One SPI controller
● One Fast-mode Plus I2C-bus interface with rates of up to 1 Mbit/s
● One Fast-mode I2C-bus interface
● Two I2S interfaces
● External Memory Controller (EMC) supporting external SRAM, ROM, flash, SDRAM
● Secure Digital Input Output (SDIO) card interface
● Eight-channel General-Purpose DMA (GPDMA) controller
● Up to 83 General-Purpose Input/Output (GPIO) pins
● Four general-purpose timer/counters with capture and match capabilities
● One motor control Pulse Width Modulator (PWM) for three-phase motor control
● One Quadrature Encoder Interface (QEI)
● Repetitive Interrupt timer (RI timer)
● Windowed watchdog timer (WWDT)
● Ultra-low power Real-Time Clock (RTC) on separate power domain
● Alarm timer; can be battery powered
● One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
● Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
● Two 128-bit secure OTP memories for AES key storage and customer use
● Crystal oscillator with an operating range of 1 MHz to 25 MHz
● 12 MHz Internal RC (IRC) oscillator trimmed to 1 % accuracy
● Ultra-low power Real-Time Clock (RTC) crystal oscillator
● Three PLLs allow CPU operation up to the maximum CPU rate
● Clock output
● Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip DC-to-DC converter
● RTC power domain can be powered separately by a 3 V battery supply
● Four reduced power modes
● Processor wake-up from Sleep mode via wake-up interrupts
● Brownout detect with four separate thresholds for interrupt and forced reset
● Power-On Reset (POR)
● See selection guide for features per type
●## Target Applications
● Industrial
● Consumer
● White goods
● RFID readers
● e-Metering
●## Features
Part 3D Model
